Information

 

We've unearthed this great article pertaining to Tools You Need to Install a New Bathtub directly below on the web and concluded it made good sense to discuss it with you on this page.

Installing a tub isn't exactly rocket science, but it does require solid plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a new one is additionally a moderately hard project. If the old tub is readily obtainable, the job can relocate speedily; if you have to open a wall surface to eliminate the old tub and also place the new tub, the task is a lot harder. In either case, the project is within a home handyman's abilities, although you will require a helper to vacate the old bathtub as well as embeded in the brand-new one. See to it you have qualified on your own for the work as well as are comfortable trying it. Rather than employing a service provider to take control of a halfway-completed job, it is better to think about utilizing one before you start. Opportunities are you may need an expert plumber to make tube connections.
This post will certainly help you install a new tub in your washroom if you have actually already bought a brand-new tub as well as don't need to alter the setup of your previous water pipelines.
Your devices and material checklist need to comprise the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Preparing for the Setup

First of all, the sustaining frame provided with the bathroom needs to be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to ensure that if the tap features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to avoid stress on the tub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should now prepare to be suited its final setting.

 

 

Removing Old Taps

If you need to replace old taps with new ones as a part of your installation, after that the first thing you should do is detach the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be rather problematic due to the limited accessibility that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have been removed, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.

 

 

Setting up the Bathtub

Using both wood boards under its feet, place the tub in the called for setting. The wood boards are handy in uniformly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small points.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub till the spirit level reviews level.
To install faucets, fit all-time low of the outermost adaptable tap port to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water system as well as inspect all joints as well as new pipework for leakages and also tighten them if essential. Fill the bathtub as well as likewise check the overflow electrical outlet and the regular outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bath tub ought to wait up until the bath tub has been utilized at the very least once as this will settle it right into its final placement.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin ensuring that the washers are in area in between the tap and also the sink. Safeguard the tap in place with the producer offered backnut. As soon as the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous type should be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Bath tub

In the location where the bath meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to crack an inflexible seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, leading to problems with wetness and possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components as well as installations. They are offered in tubes and cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill the tub with water before securing, to permit the movement experienced when the tub is in use. The sealant can break fairly early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily available on the market. It is suggested to fit the floor tiles utilizing waterproof or water-proof adhesive and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We had been made aware of that report on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an associate on another blog. Do you know somebody who is enthusiastic about the niche? Do not hesitate to share it. Thank-you for taking the time to read it.

View